Pole splitting

In electronics, pole splitting is a form of frequency compensation used in an electronic amplifier to increase the stability of the amplifier and improve its step response at the cost of decreased speed. By introduction of a capacitor between the input and output sides of the amplifier, the amplifier pole lowest in frequency (usually an input pole) moves to a lower frequency, and a pole higher in frequency (usually an output pole) moves to a still higher frequency: hence the name pole splitting.

Example of pole splitting

(PD) Image: John R. Brews
Operational amplifier with compensation capacitor C_C between input and output; notice the amplifier has both input impedance R_i and output impedance R_o.

(PD) Image: John R. Brews
Operational amplifier with compensation capacitor transformed using Miller's theorem to replace the compensation capacitor with a Miller capacitor at the input and a frequency-dependent current source at the output.

This example shows two results of introduction of the compensation capacitor denoted as C_C in the amplifier of the figure to the right: first, it causes the lowest frequency pole of the amplifier to move still lower in frequency and second, it causes the higher pole to move higher in frequency. The amplifier in the figure has a low frequency pole due to the added input resistance R_i and capacitance C_i, with the time constant C_i ( R_A // R_i ). This pole is moved down in frequency by the Miller effect. The amplifier is given a high frequency output pole by addition of the load resistance R_L and capacitance C_L, with the time constant C_L ( R_o // R_L ). The upward movement of the high-frequency pole occurs because the Miller-amplified compensation capacitor C_C alters the frequency dependence of the output voltage divider.

The first objective, to show the lowest pole moves down in frequency, is established using the same approach as the Miller's theorem article. Following the procedure described in the article on Miller effect, the amplifier circuit is transformed to that of the next figure, which is electrically equivalent. Application of Kirchhoff's current law to the input side of the transformed circuit determines the input voltage $\ v_{i}$ to the ideal op amp as a function of the applied signal voltage $\ v_{a}$, namely,

${\frac {v_{i}}{v_{a}}}={\frac {R_{i}}{R_{i}+R_{A}}}{\frac {1}{1+j\omega (C_{M}+C_{i})(R_{A}//R_{i})}}\ ,$

which exhibits a roll-off with frequency beginning at f₁ where

${\begin{aligned}f_{1}&={\frac {1}{2\pi (C_{M}+C_{i})(R_{A}//R_{i})}}\\&={\frac {1}{2\pi \tau _{1}}}\ ,\\\end{aligned}}$

which introduces notation $\tau _{1}$ for the time constant of the lowest pole. This frequency is lower than the initial low frequency of the amplifier, f₀ say, which for C_C = 0 F is:

$f_{0}={\frac {1}{2\pi C_{i}(R_{A}//R_{i})}}\ .$

Turning to the second objective, showing the higher pole moves still higher in frequency, it is necessary to look at the output side of the circuit, which contributes a second factor to the overall gain, and additional frequency dependence. The voltage $\ v_{o}$ is determined by the gain of the ideal op amp inside the amplifier as

$\ v_{o}=A_{v}v_{i}\ .$

Using this relation and applying Kirchhoff's current law to the output side of the circuit determines the load voltage $v_{\ell }$ as a function of the voltage $\ v_{i}$ at the input to the ideal op amp as:

${\frac {v_{\ell }}{v_{i}}}=A_{v}{\frac {R_{L}}{R_{L}+R_{o}}}\,\!$$\cdot {\frac {1+j\omega C_{C}R_{o}/A_{v}}{1+j\omega (C_{L}+C_{C})(R_{o}//R_{L})}}\ .$

This expression is combined with the gain factor found earlier for the input side of the circuit to obtain the overall gain as

${\frac {v_{\ell }}{v_{a}}}={\frac {v_{\ell }}{v_{i}}}{\frac {v_{i}}{v_{a}}}$

$=A_{v}{\frac {R_{i}}{R_{i}+R_{A}}}\cdot {\frac {R_{L}}{R_{L}+R_{o}}}\,\!$$\cdot {\frac {1}{1+j\omega (C_{M}+C_{i})(R_{A}//R_{i})}}\,\!$$\cdot {\frac {1+j\omega C_{C}R_{o}/A_{v}}{1+j\omega (C_{L}+C_{C})(R_{o}//R_{L})}}\ .$

This gain formula appears to show a simple two-pole response with two time constants. (It also exhibits a zero in the numerator but, assuming the amplifier gain A_v is large, this zero is important only at frequencies too high to matter in this discussion , so the numerator can be approximated as unity.) However, although the amplifier does have a two-pole behavior, the two time-constants are more complicated than the above expression suggests because the Miller capacitance contains a buried frequency dependence that has no importance at low frequencies, but has considerable effect at high frequencies. That is, assuming the output R-C product, C_L ( R_o // R_L ), corresponds to a frequency well above the low frequency pole, the accurate form of the Miller capacitance must be used, rather than the Miller approximation. According to the article on Miller effect, the Miller capacitance is given by:

${\begin{aligned}C_{M}&=C_{C}\left(1-{\frac {v_{\ell }}{v_{i}}}\right)\\&=C_{C}\left(1-A_{v}{\frac {R_{L}}{R_{L}+R_{o}}}{\frac {1+j\omega C_{C}R_{o}/A_{v}}{1+j\omega (C_{L}+C_{C})(R_{o}//R_{L})}}\right)\ .\quad \quad {\text{(Miller equation)}}\\\end{aligned}}$

(For a positive Miller capacitance, A_v is negative.) Upon substitution of this result into the gain expression and collecting terms, the gain is rewritten as:

${\frac {v_{\ell }}{v_{a}}}=A_{v}{\frac {R_{i}}{R_{i}+R_{A}}}{\frac {R_{L}}{R_{L}+R_{o}}}{\frac {1+j\omega C_{C}R_{o}/A_{v}}{D_{\omega }}}\ ,$

with D_ω given by a quadratic in ω, namely:

$D_{\omega }\,\!$ $=[1+j\omega (C_{L}+C_{C})(R_{o}//R_{L})]\,\!$ $\cdot \ [1+j\omega C_{i}(R_{A}//R_{i})]\,\!$ $\ +j\omega C_{C}(R_{A}//R_{i})\,\!$ $\cdot \left(1-A_{v}{\frac {R_{L}}{R_{L}+R_{O}}}\right)\,\!$ $\ +(j\omega )^{2}C_{C}C_{L}(R_{A}//R_{i})(R_{O}//R_{L})\ .$

Every quadratic has two factors, and this expression looks simpler if it is rewritten as

$\ D_{\omega }=(1+j\omega {\tau }_{1})(1+j\omega {\tau }_{2})$

$=1+j\omega ({\tau }_{1}+{\tau }_{2}))+(j\omega )^{2}\tau _{1}\tau _{2}\ ,\$

where $\tau _{1}$ and $\tau _{2}$ are combinations of the capacitances and resistances in the formula for D_ω. They correspond to the time constants of the two poles of the amplifier. One or the other time constant is the longest; suppose $\tau _{1}$ is the longest time constant, corresponding to the lowest pole, and suppose $\tau _{1}$ >> $\tau _{2}$. (Good step response requires $\tau _{1}$ >> $\tau _{2}$. See Selection of C_C below.)

At low frequencies near the lowest pole of this amplifier, ordinarily the linear term in ω is more important than the quadratic term, so the low frequency behavior of D_ω is:

${\begin{aligned}\ D_{\omega }&=1+j\omega [(C_{M}+C_{i})(R_{A}//R_{i})+(C_{L}+C_{C})(R_{o}//R_{L})]\\&=1+j\omega (\tau _{1}+\tau _{2})\approx 1+j\omega \tau _{1}\ ,\ \\\end{aligned}}$

where now C_M is redefined using the Miller approximation as the ω=0 limit of the previous expression for the Miller capacitance C_M found above:

$C_{M}=C_{C}\left(1-A_{v}{\frac {R_{L}}{R_{L}+R_{o}}}\right)\ .\quad \quad {\text{(Miller approximation)}}$

On this basis $\tau _{1}$ is determined, provided $\tau _{1}$ >> $\tau _{2}$. Because C_M is large, the time constant ${\tau }_{1}$ is much larger than its original value of C_i ( R_A // R_i ).

At high frequencies the quadratic term becomes important. Assuming the above result for $\tau _{1}$ is valid, the second time constant, the position of the high frequency pole, is found from the quadratic term in D_ω as

$\tau _{2}={\frac {\tau _{1}\tau _{2}}{\tau _{1}}}\approx {\frac {\tau _{1}\tau _{2}}{\tau _{1}+\tau _{2}}}\ .$

Substituting in this expression the quadratic coefficient corresponding to the product $\tau _{1}\tau _{2}$ along with the estimate for $\tau _{1}$, an estimate for the position of the second pole is found:

${\begin{aligned}\tau _{2}&={\frac {(C_{C}C_{L}+C_{L}C_{i}+C_{i}C_{C})(R_{A}//R_{i})(R_{O}//R_{L})}{(C_{M}+C_{i})(R_{A}//R_{i})+(C_{L}+C_{C})(R_{o}//R_{L})}}\\&\approx {\frac {C_{C}C_{L}+C_{L}C_{i}+C_{i}C_{C}}{C_{M}}}(R_{O}//R_{L})\ ,\\\end{aligned}}$

and because C_M is large, it seems $\tau _{2}$ is reduced in size from its original value C_L ( R_o // R_L ); that is, the higher pole has moved still higher in frequency because of C_C.

In short, introduction of capacitor C_C moved the low pole lower and the high pole higher, so the term pole splitting seems a good description.

Selection of C_C

(PD) Image: John R. Brews
Idealized Bode plot for a two pole amplifier design. Gain drops from first pole at f₁ at 20 dB / decade down to second pole at f₂ where the slope increases to 40 dB / decade.

What value is a good choice for C_C? For general purpose use, traditional design (often called dominant-pole or single-pole compensation) requires the amplifier gain to drop at 20 dB/decade from the corner frequency down to 0 dB gain, or even lower. With this design the amplifier is stable and has near-optimal step response even as a unity gain voltage buffer. A more aggressive technique is two-pole compensation.

The way to position f₂ to obtain the design is shown in the adjacent Bode plot. At the lowest pole f₁, the Bode gain plot breaks slope to fall at 20 dB/decade. The aim is to maintain the 20 dB/decade slope all the way down to zero dB, and taking the ratio of the desired drop in gain (in dB) of 20 log₁₀ A_v to the required change in frequency (on a log frequency scale) of ( log₁₀ f₂  − log₁₀ f₁ ) = log₁₀ ( f₂ / f₁ ) the slope of the segment between f₁ and f₂ is:

Slope per decade of frequency $=20{\frac {\mathrm {log_{10}} (A_{v})}{\mathrm {log_{10}} (f_{2}/f_{1})}}\ ,$

which is 20 dB/decade provided f₂ = A_v f₁ . If f₂ is not this large, the second break in the Bode plot that occurs at the second pole interrupts the plot before the gain drops to 0 dB with consequent lower stability and degraded step response.

The Bode plot shows that to obtain the correct gain dependence on frequency, the second pole is at least a factor A_v higher in frequency than the first pole. The gain is reduced a bit by the voltage dividers at the input and output of the amplifier, so with corrections to A_v for the voltage dividers at input and output the pole-ratio condition for good step response becomes:

${\frac {\tau _{1}}{\tau _{2}}}\approx A_{v}{\frac {R_{i}}{R_{i}+R_{A}}}\cdot {\frac {R_{L}}{R_{L}+R_{o}}}\ ,$

(PD) Image: John R. Brews
Miller capacitance at low frequencies C_M (top) and compensation capacitor C_C (bottom) as a function of gain using Excel. Capacitance units are pF.

Using the approximations for the time constants developed above,

${\frac {\tau _{1}}{\tau _{2}}}\approx {\frac {(\tau _{1}+\tau _{2})^{2}}{\tau _{1}\tau _{2}}}\approx A_{v}{\frac {R_{i}}{R_{i}+R_{A}}}\cdot {\frac {R_{L}}{R_{L}+R_{o}}}\ ,$

or

${\frac {[(C_{M}+C_{i})(R_{A}//R_{i})+(C_{L}+C_{C})(R_{o}//R_{L})]^{2}}{(C_{C}C_{L}+C_{L}C_{i}+C_{i}C_{C})(R_{A}//R_{i})(R_{O}//R_{L})}}\,\!$ ${\color {White}\cdot }=A_{v}{\frac {R_{i}}{R_{i}+R_{A}}}\cdot {\frac {R_{L}}{R_{L}+R_{o}}}\ ,$

which provides a quadratic equation to determine an appropriate value for C_C.

The figure shows an example using this equation. At low values of gain this example amplifier satisfies the pole-ratio condition without compensation (that is, in the figure the compensation capacitor C_C is small at low gain), but as gain increases, a compensation capacitance rapidly becomes necessary (that is, in the figure the compensation capacitor C_C increases rapidly with gain) because the necessary pole ratio increases with gain. For still larger gain, the necessary C_C drops with increasing gain because the Miller amplification of C_C, which increases with gain (see the Miller approximation above), allows a smaller value for C_C.

To provide more safety margin for design uncertainties, often A_v is increased to two or three times A_v on the right side of this equation. See Sansen or Huijsing and article on step response.

Slew rate

The above is a small-signal analysis. However, when large signals are used, the need to charge and discharge the compensation capacitor adversely affects the amplifier slew rate; in particular, the response to an input ramp signal is limited by the need to charge C_C.