Crossflow membrane filtration

Crossflow filtration is a term used to refer to a membrane filtration technique in which feed flows parallel to the membrane, rather than perpendicular to the membrane as in conventional filtration. It is typically characterized by having high tangential fluid velocity and a low velocity normal to the membrane. Crossflow filtration is used in many applications of downstream processing including food processing, pharmaceutical production, and cell separation. This type of separation is typically used because of it is simple, cost effective, and has high throughput rates.

Comparison with conventional filtration

In an ideal crossflow filtration system, the flux of permeate through the membrane will reach a steady state. This allows for much easier continuous removal of the target material when compared with conventional filtration.

Typical crossflow membrane operation.

In practical applications, though, a cake builds up along the membrane. The cake increases in thickness through the length of the membrane filter until steady state is reached, as shown in the figure to the right.

Additionally, because the fluid flow is parallel to the membrane, rather than perpendicular to it as in conventional filtration systems, shear along the membrane prevents continual cake buildup. This contributes to the easy and continuous removal of the target material and reduces the need for cake washing. A boundary layer still develops along the membrane, but is usually very thin. Fouling of the membrane can still occur, along with concentration polarization, in which a gel layer forms and reduces transmembrane flux.

Membrane fouling

Though fouling is significantly reduced in crossflow membrane systems, as compared with conventional filtration systems, it is still a problem. Depending on the type of filter used and the pore sizes, different problems can arise. Concentration polarization can become exacerbated by gel formation in ultrafiltration systems, and microfiltration of suspended particles can create

Fouling of membrane pores.

thick cake layers that reduce transmembrane flux. Large, soft particles can adhere to the pores, smaller particles can clog pores, and precipitates can form on the pores all reducing the pore size available and reducing transmembrane flux. Types of pore plugging can be seen in Figure 3 to the left. Gel layer formation can sometimes be reduced by mechanical agitation.

Typical Operation

Standard operating conditions and calculations vary depending upon the feed used, and are affected by how the feed interacts with the solution, the physical size and quantity of the target(s) of filtration in the feed, and whether the targets are dissolved or simply suspended in solution. Quantitatively, filtration flux (J) across the membrane can be calculated by dividing the driving force (∆P_m, typically the transmembrane pressure drop) by the overall membrane resistance (R_G + R_M). The gel resistance, R_G, usually increases with time until the membrane is cleaned, and the resistance of the membrane, R_M, is often assumed to stay constant.

Dissolved Species

As the feed flows across the membrane, dissolved molecules will be rejected by the membrane. When this occurs, a concentration gradient develops along the membrane where molecules are in higher concentrations than that of the solution. Membranes with small enough pore sizes, such as those used in ultrafiltration, can even remove dissolved species and form a gel layer that impedes transmembrane flux.

Suspended Species

Crossflow membrane filtration that involves suspended particles will generate a cake layer that is similar to the gel layer of an ultrafiltration system and is shown in Figure 1. The cake layer will continue to increase, constricting the fluid flow channel and reducing transmembrane flux of the filtrate until steady state is reached. For particles greater than 1μm in diameter typical dissolved species flux equation is no longer valid and shear-induced diffusion theory created by Zydney and Colton can be used.

Concentration Polarization

Concentration polarization along a membrane is experienced when the solute concentration at the membrane reaches elevated levels in comparison to the feed bulk fluid concentration. {ref name=Harrison2003/} The concentration gradient of dissolved species rejected at the membrane can be described by the following equation:

${\frac {c_{m}}{c_{\delta }}}=exp\left({\frac {J\delta }{D}}\right)$, where

δ = distance from the membrane

c_m = concentration at the membrane

c_δ = concentration at a distance δ from the membrane

J = transmembrane fluid flux

D = Diffusion coefficient

When concentration polarization reaches very high levels, it can cause precipitation of the solute, which forms a gel layer at the surface of the membrane. At times, this effect can become great enough that fluid flow across the membrane is significantly reduces. {ref name=Harrison2003/} Concentration polarization can be difficult to control, depending on the specific filtration, but it can be reduced in several ways. Running the filtration at a lower operation pressure, shortening the flow length, or creating turbulence by using thing flow channels or with additional mixing, can all reduce concentration polarization. Other more complicated methods of reducing concentration polarization include mechanical scouring, shaking, or skimming to remove the boundary layer. These are less ideal as they can effect the integrity of the membrane. _{Subscript text}

Applications of crossflow filtration

Many different types of filtration exist that are specific to different particle sizes. Choosing the appropriate one depends on the target that is being selected for and the key impurities that will be removed. Different types of filters are shown in the table below and include: microfiltration, ultrafiltration, nanofiltration, and reverse osmosis.

Size	Molecular Weight	Example Particle	Membrane Process
100 μm		Pollen	Microfiltration
10μm		Starch	Microfiltration
1μm		Blood Cells, Bacteria	Microfiltration
100Å	100,000	Albumin, Pepsin	Ultrafiltration
10Å	1,000-10,000	Vitamin B12, Glucose	Ultrafiltration, Nanofiltration
1Å		Water, Sodium Chloride	Reverse Osmosis

One particular type of crossflow membrane device is the hollow fiber membrane. In hollow fiber filter systems, the feed flow is run through many tiny hollow tubes and molecules are allowed to diffuse in and out normal to the fluid flow through the tubes. This is commonly used in dialysis of human blood.