Precipitation (chemistry)

All unapproved Citizendium articles may contain errors of fact, bias, grammar etc. A version of an article is unapproved unless it is marked as citable with a dedicated green template at the top of the page, as in this version of the 'Biology' article. Citable articles are intended to be of reasonably high quality. The participants in the Citizendium project make no representations about the reliability of Citizendium articles or, generally, their suitability for any purpose. This article is currently being developed as part of an Eduzendium student project in the framework of a course entitled BEE 4640 Bioseparation Processes at Cornell University. The course homepage can be found at CZ:Cornell_University_2010_BEE_4640_Bioseparation_Processes. For the course duration, the article is closed to outside editing. Of course you can always leave comments on the discussion page. The anticipated date of course completion is 21 December 2010. One month after that date at the latest, this notice shall be removed. Besides, many other Citizendium articles welcome your collaboration! Note to course participants: Looking forward to some insightful and useful articles from your collaborations.

A brief overview of your bioseparation topic (be sure to put its name in bold in the first sentence) and the scope of the article goes here.Also see CZ:How to start a new article

The following list of sections may serve as a loose guideline for developing the body of your article. Before deciding to follow it, take a look at some other articles on subjects like your own. You may like their structure better and if so, adopt it.

The works cited in references 2-5 are all fake (and are borrowed from another Eduzendium template); their purpose is to serve as a formatting model for your own citations.

The Process

Introduction

The process by which a dissolved chemical species comes out of solution as a solid is called precipitation. It is often employed in bioseparation applications for protein purification and concentration, although it may be used to isolate other compounds, such as nucleic acids and other cell components. Precipitation is achieved by altering the solubility of a target protein in a solution to cause it to become insoluble and thus precipitate, allowing for this concentrated solid to be more easily separated from the liquid phase (supernatant).

Solubility of Macromolecules

Solubility is the property of a substance (solute) – in either gas, liquid, or solid phases – that determines the extent to which it dissolves in a liquid (called the solvent) and form a homogenous (single-phase) solution. It is based on factors such as temperature, compatibility between the solute’s net charge and the solvent’s polarity, the formation of hydration layers, the presence and concentration of other solutes dissolved in the solvent, and solvent’s ionic strength and dielectric constant.

Macromolecules (such as proteins and nucleic acids) are typically present in aqueous solvents. They are able to dissolve as a result of assuming a stable conformation in the solvent and then being surrounded by hydration layer(s). When placed in an aqueous solution, the macromolecules adopt a structure in which most hydrophobic (nonpolar) portions of the molecules gather inwards, and most hydrophilic (charged/polar) portions surround the exterior, guided to a final conformation that has the lowest Gibbs free energy. The attraction between the hydrophilic surface of the macromolecule and the polar water molecules creates an interface in which similarly-oriented water molecules associate with, and surround, the solute’s surface to form a highly ordered layer, called the hydration layer (also called the interfacial double layer). The formation of hydration layers enhances the solubility of macromolecules by greatly reducing inter-macromolecular dipole-dipole attraction and thus preventing their association with other solutes.

Effects of Solute Net Charge

In an aqueous solvent solutes with a higher net charge are more soluble, due to their enhanced ability to associate with water molecules and create a hydration layer, and their lessened inter-solute interactions as a result of increased repulsion from like-charges.

Effects of Solvent Ionic Strength

Increasing a solvent’s ionic strength (the concentration of ions in solution) decreases the availability of unassociated water molecules, which are required for the formation of hydration layers. This increases intermolecular attraction between solutes and promotes coalescence, thus decreasing the solute’s solubility.

Common Methods of Precipitation

Salting Out

A common method of protein precipitation is called salting out, and is achieved by increasing an aqueous solvent’s ionic strength by dissolving a salt. Increases in salt concentrations steadily decrease the solubility of proteins in the solution, until the proteins become insoluble and precipitate out of solution. Since proteins generally differ in their solubility, slowly adding salt allows for selective precipitation of dissolved proteins in order of lowest to highest solubility. This process is described empirically by the Cohn equation:
$ln(S)=\beta -K_{s}^{'}*I$
where $S$ is the solubility of the protein in mol/L, $\beta$ is the solubility at zero ionic strength in mol/L, $K_{s}^{'}$ is the protein’s characteristic salting-out constant (no units), and $I$ is the concentration of ions in solution in mol/L.

The most commonly used salt for this procedure is ammonium sulfate, (NH₄)₂SO₄ due to its high solubility, lack of buffering capacity, minimal cost, and the low density of the resulting solution relative to other salts, which aids in centrifugation separation.

Isoelectric Precipitation

At its isoelectric pH, called the pI, a macromolecule possesses no net charge and thus no like-charge repulsion occurs between solutes. This results in weaker interactions with water molecules and makes the macromolecule more hydrophobic, increasing its affinity for combining with other solutes, and thus allowing for precipitation.

Changing Solvents & Alcohol Precipitation

The addition of a nonpolar solvent like ethanol to a solution typically decreases solubility of highly charged solutes, and is commonly used in nucleic acid precipitation. The nonpolar alcohols compete with water for association with the dissolved solute and destabilize the hydration layer, increasing the solute’s ability to form hydrophobic interactions with other solutes, and decreasing its solubility as a result.

Flocculation

Flocculation is a process in which particles of an insoluble, dispersed (but not dissolved), and colloidal substance join together to form what are called flocs, which are flaky aggregations of the substance. Typically, most biological particles suspended in a solution possess a negative charge reference. This creates repulsion between the particles, which is counteracted by a mutual attraction due to van der Waals force. Although at short range the van der Waals force is much more powerful, it decays rapidly with distance and the inter-particle repulsive forces, which act a greater range, typically prevent particles from achieving this required approach distance.

Flocculation is achieved by minimizing the contribution of repulsive forces in order to maximize the effect of the van der Waals force, to an extent that allows the particles to move sufficiently close to permit the van der Waals force to drive particle aggregation. The most common process to produce this effect is to increase the ionic strength of the solution by dissolving a salt, whose charged ions interfere with inter-solute repulsion.

Precipitate Formation

When the concentration of a solute is greater than its equilibrium solubility, it is termed supersaturated. The process of precipitation begins in a supersaturated solution first by nucleation, in which ultramicroscopic clusters of particles are generated. Following nucleation, diffusion-limited growth of the particles occurs until the particles reach a diameter limited by the shear field of the fluid. The rate at which particles aggregate may be described by the following rate equation:
$-{\frac {dN}{dt}}=8{\pi }DL_{mol}N^{2}$
where $N$ is the number of the ultramicroscopic clusters initially created by nucleation, $D$ is the diffusivity, and $L_{mol}$ is the diameter of the particles. Integrating the equation gives:
${\frac {N}{N_{0}}}={\frac {1}{1+N_{0}K_{A}t}}$
where $N_{0}$ is the initial number of particles. After reaching their critical size, the clusters undergo a flocculation process in which their continued growth is governed by fluid motion, which causes them to collide and stick together. This growth is described by the equation:
${\frac {N}{N_{0}}}=exp(-{\frac {2{\alpha }L^{3}NGt}{3}})$
where ${\alpha }$ is the fraction of collisions that result in permanent aggregates, $N$ is the number of particles, $t$ is time elapsed, $L$ is the diameter of the particles, and $G$ is the shear rate. The flocs reach a stable size after a period called the “aging” time elapses.

History

This section should describe the invention and development of the process. If the section runs long, divide it into chronological subsections, for example:

Invention and early development

This subsection should provide some historical context for the development of your process, describe its invention, and name some early developers and/or applications.

Recent developments

This section should discuss new developments in the field. Don't hesitate to drop in brief mentions of processes or features you don't intend to discuss in depth. By so doing you are planting seeds of articles which will eventually be developed by others.

Design and Operation

Use lots of subsections here as you describe various aspects of the process .

Applications

This section should discuss how the process is used in practice.

Examples

If you have used a lot of equations in your article, this may be a good place to show an example of how they are used. See the article on the Antoine Equation for an example.